PDA

View Full Version : "That's No Programmed Effect; It's A Glitch!"


Master Neb
07-19-2010, 06:17 PM
Moved to the work bench the forum for threads like this... -- j7

"That's no programmed effect; it's a glitch!"
Kotor ii wont work on my my computer though it should meet system requirements:
XP media center edition
Processor

Processor type

Intel® Pentium® 4 5XXX and 6XXX processors with Hyper-Threading technology

NOTE: Not all Pentium 4 processors support Hyper-Threading technology.

Level 1 (L1) cache

16 KB

Level 2 (L2) cache

1 MB for Pentium 5XXX processors

2 MB for Pentium 6XXX processors

(depending on your computer configuration) pipelined-burst, eight-way set associative, write-back SRAM

Memory

Type

400-MHz and 533-MHz DDR2 unbuffered SDRAM

Memory connectors

four

Memory capacities

256 MB, 512 MB, or 1 GB non-ECC

Maximum memory

4 GB

NOTE: See "Addressing Memory With 4-GB Configurations" to verify the amount of memory available to the operating system.

BIOS address

F0000h

Computer Information

Chipset

Intel 945G Express

RAID Support

RAID 1 (Mirroring)

DMA channels

eight

Interrupt levels

24

BIOS chip (NVRAM)

4 Mb

NIC

Integrated network interface capable of 10/100 communication

System clock

800- or 1066-MHz data rate

Video

Type

Integrated Intel Graphics Media Accelerator 950 (GMA950)

Audio

Type

Sigmatel STAC9220

Expansion Bus

Bus type

PCI 2.3
PCI Express x1 and x16

Bus speed

PCI: 33 MHz

PCI Express:

x1 slot bidirectional speed - 500 MB/s

x16 slot bidirectional speed - 8 GB/s

PCI



connectors

two

connector size

120 pins

connector data width (maximum)

32 bits

PCI Express



connector

one x1

connector size

36 pins

connector data width (maximum)

1 PCI Express lane

PCI Express



connector

one x16

connector size

164 pins

connector data width (maximum)

16 PCI Express lanes

Drives

Externally accessible:



one 3.5-inch FlexBay (may contain an optional floppy drive or an optional Media Card Reader)

two 5.25-inch drive bays

Available devices

Serial ATA drives (2), floppy drive, USB memory devices, CD drive, CD-RW drive, DVD drive, DVD-RW drive, DVD and CD-RW combo drive, and Media Card Reader

Internally accessible:

two bays for 1-inch high serial ATA hard drives

Connectors

External connectors:

Video

15-hole connector

Network adapter

RJ-45 connector

USB

two front-panel and five back-panel USB 2.0-compliant connectors

Audio

five connectors for line-in, line-out, microphone/ side-surround, surround, and center/subwoofer connector (LFE channel); two front-panel connectors for headphones and microphone

System board connectors:

Primary IDE drive

one 40-pin connector

Serial ATA

two 7-pin connectors

FlexBay Drive

one USB 10-pin header for optional Media Card Reader (3.5-inch bay device)

Floppy drive

one 33-pin connector

Fan

one 5-pin connector

PCI 2.3

two 120-pin connectors

PCI Express x1

one 36-pin connector

PCI Express x16

one 164-pin connector

Controls and Lights

Power button

push button

Power light

green light — Blinking green in sleep state; solid green for power-on state.

amber light — Blinking amber indicates a problem with the power supply inside the computer. If the system cannot boot and there is a solid amber light, this indicates a problem with the system board (see "Power Problems" in your computer Owner's Manual).

Hard-drive access light

green

Link integrity light (on integrated network adapter)

green light — A good connection exists between a 10-Mbps network and the computer.

orange light — A good connection exists between a 100-Mbps network and the computer.

off (no light) — The computer is not detecting a physical connection to the network.

Activity light (on integrated network adapter)

yellow blinking light

Diagnostic lights

four lights on the front panel (see "Diagnostic Lights")

Standby power light

AUX_PWR on the system board

Power

DC power supply:

Wattage

305 W

Heat dissipation

1041 BTU/hr

Voltage (see the safety instructions in the Product Information Guide for important voltage setting information)

90 to 135 V and 180 to 265 V at 50/60 Hz

Backup battery

3-V CR2032 lithium coin cell

Physical

Height

41.1 cm (16.2 inches)

Width

18.8 cm (7.4 inches)

Depth

45.7 cm (18.0 inches)

Weight

14.3 kg (31.4 lb)

Environmental

Temperature:

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

20% to 80% (noncondensing)

Maximum vibration:

Operating

0.25 G at 3 to 200 Hz at 0.5 octave/min

Storage

0.5 G at 3 to 200 Hz at 1 octave/min

Maximum shock:

Operating

bottom half-sine pulse with a change in velocity of 20 inches/sec (50.8 cm/sec)

Storage

27-G faired square wave with a velocity change of 200 inches/sec (508 cm/sec)

Altitude:

Operating

–15.2 to 3048 m (–50 to 10,000 ft)

Storage

–15.2 to 10,668 m (–50 to 35,000 ft)

jonathan7
07-19-2010, 09:05 PM
Have you checked the various Stickes in this forum, such as this (click me) (http://www.lucasforums.com/showthread.php?t=167523) thread?

mrk1949lf
07-19-2010, 11:21 PM
Have you checked the various Stickes in this forum, such as this (click me) (http://www.lucasforums.com/showthread.php?t=167523) thread?

the links to AMD are all 404

jonathan7
07-20-2010, 05:20 AM
the links to AMD are all 404

Only one of the links isn't going anywhere for me, though my browser link correction maybe better than yours as it's just sending me straight to the AMD site. I'll have a search and update links if I can track down the info/downloads.

Q
07-20-2010, 08:30 PM
Try using the game's configuration utility to post your system specs:
Post your system specs
Sometimes we're just not going to be able to help you if we don't know what kind of hardware you have on your machine. If you don't know what you have on your machine, then follow these steps below:
Bring up the launcher menu for Kotor 1 or 2.
Click on "Configure".
Click the "Scan Hardware" button on the lower center of the window.
Click "Yes" to continue.
Click "Details" to view your system specs.
Click "Save Report" and save the file to your desktop.
Whenever you post your problem, open the file you just saved and copy and paste the contents to your post.